Get set up in a few minutes
Two ways to connect. Hotspot mode is the default and needs a Tesla with the built-in web browser. Relay mode needs no hotspot but needs a car with its own internet connection.
Before you start
Set up Dashbeam only while parked, or have a passenger do it. The driver should never operate the phone or the car screen while driving. Rules about screens that the driver can see vary by country and region, and you are responsible for following them.
- An iPhone with the Dashbeam app, and a Tesla with its built-in web browser.
- Waze or Google Maps on the phone, or whatever you want to show.
- A phone mount, ideally in landscape, and a charging cable.
Hotspot mode
The video goes directly from the phone to the car on the local hotspot link. It is not sent to any server.
While your car is joined to your phone's hotspot, the car can also use that connection for its own software updates and drive-data uploads, and those can be many gigabytes. Before you rely on hotspot mode, check your mobile plan's hotspot allowance, and pause or limit software updates and data uploads in the car while it is on your hotspot. The menu names for these settings vary between Tesla software versions, so look in the car's Software and Controls settings, or in the owner's manual.
Turn on Personal Hotspot
On the iPhone, open Settings, then Personal Hotspot, and turn on Allow Others to Join. Keep that screen open the first time so the phone is easy to find from the car.
Join it from the car
On the car screen, open Controls, then Wi-Fi, and choose your iPhone from the list. Enter the hotspot password if asked. Wait until the car shows it is connected.
Start the app and read the address
Open Dashbeam on the iPhone. It shows an address like
http://172.20.10.1:8080. Your address may differ, so use the one the app shows. If iOS asks to allow local network access, tap Allow.Open the address in the car browser
In the car's web browser, type the address exactly as shown, including
http://. Then bookmark it so next time it is one tap.Start mirroring on the phone
In Dashbeam, tap Start Mirroring, then confirm in the iOS broadcast sheet. iOS requires this every time. Then open Waze or Google Maps on the phone and start your route.
Check the picture
The map should appear on the car screen. The stats panel in the app shows frames per second and data rate. Choose a crop preset, Fit or Fill, and a quality preset (Battery saver, Balanced or Sharp). Quality changes apply instantly.
Relay mode
Relay mode is a Premium feature, free while testing. It uses your phone's mobile data (very roughly 0.3 to 1 GB per hour) and the car's data. The phone screen, which can include your location on the map, passes through the server live and is not recorded or stored.
Make sure the car is online
Relay mode needs the car to have its own internet connection, such as Tesla Premium Connectivity, or another connection the car can use. You do not need the iPhone hotspot.
Open the Dashbeam page in the car
In the car's browser, go to
https://api.dashbeam.app/carand bookmark it. The page shows a 6-digit pairing code.Enter the code in the app
In Dashbeam on the iPhone, choose Relay mode and type the 6-digit code. Codes are short-lived and work once. You only need to pair once, and the app and the car page remember each other afterwards.
Start mirroring
Tap Start Mirroring on the phone and confirm in the iOS sheet. Open your map app. The picture passes through Dashbeam's server live and is not recorded or stored.
Tips for a good picture
- Mount the phone in landscape. It matches the car screen and gives the largest map.
- Keep it charging and out of direct sunlight.
- Pick a crop preset that hides the status bar, then choose Fit or Fill.
- Start with Balanced quality. Switch to Battery saver if the phone is warm or the link is weak, or Sharp if the link is strong.
- Remember it is view-only. Control the map on the phone before you drive, or by voice. Directions audio plays through the car over Bluetooth as usual.
Troubleshooting
iOS asks to allow local network access
Tap Allow. Hotspot mode needs it so the car can reach the phone. If you tapped Don't Allow, open iPhone Settings, then Dashbeam, and turn Local Network on.
The picture does not appear on the car
- Check that the car is still joined to your iPhone's hotspot and that the address matches the one in the app.
- Make sure you typed
http://, nothttps://. - Confirm you tapped Start Mirroring and the status in the app says it is running.
- Close the car browser tab and open your bookmark again.
- Turn the hotspot off and on, then rejoin from the car.
The car will not join the hotspot
- Keep the iPhone's Personal Hotspot screen open while the car searches.
- Turn on Maximize Compatibility in Personal Hotspot settings if your iPhone offers it. It uses the 2.4 GHz band, which many car systems prefer.
- Forget the network in the car's Wi-Fi list and join again.
- Restart the phone's hotspot, and if needed restart the phone.
The picture freezes or the car page disconnects
The car page reconnects automatically and keeps the last picture on screen meanwhile. If it does not come back, check the phone has not locked or the hotspot has not switched off, then tap Start Mirroring again. Try the Battery saver quality preset if the connection is weak.
I have to tap Start Mirroring every time
Yes. iOS requires you to approve a screen broadcast each time, and apps cannot start it on their own.
The picture is too small or has black bars
Try the Fill layout, or a different crop preset to remove the phone's status bars. A landscape phone mount usually gives the best result because the phone's shape then matches the car screen.
The phone is getting hot
Running navigation, screen capture and a hotspot together is demanding. Keep the phone plugged in, out of direct sun, and with some airflow, for example in a vent mount. Use the Battery saver preset, and lower the phone's screen brightness. If iOS shows a temperature warning, stop mirroring and let it cool.
The car page works on hotspot but my data is disappearing
The car may be using your hotspot for software updates or data uploads. Pause or limit those in the car while on the hotspot, and check your plan's hotspot allowance.
Relay mode: the code does not work
Codes expire quickly and work once. Reload the car page to get a fresh code, and type it into the app straight away. Both the phone and car need an internet connection.
Still stuck? See the support page or email support@dashbeam.app.